欢迎访问济南科尔超声波设备有限公司网站!

专注生产工业用清洗设备

让工业清洗无难事

电话

业务咨询电话:

18663767799

你所在位置: 首页-新闻动态-新闻资讯-操作超声波清洗机的正确注意事项
新闻资讯

操作超声波清洗机的正确注意事项

作者:guanli来源:http://www.jnthcsb.com/时间:2022-11-12

全自动超声波清洗机的操作是有明确要求的,如果操作失误,那么可能会让设备受损,甚至可能带来事故,下面这几点是操作超声波清洗机一定要注意的。
There are clear requirements for the operation of the automatic ultrasonic cleaner. If the operation is wrong, the equipment may be damaged, or even cause accidents. The following points must be paid attention to when operating the ultrasonic cleaner.
特别要注意的是全自动超声波清洗机定要接地良好,把清洗机放置在清洁干燥的地方,使用过程中避免设备产生剧烈的振动,还要确保有良好的散热条件。
Special attention should be paid to the fact that the fully automatic ultrasonic cleaning machine must be well grounded, placed in a clean and dry place, avoid violent vibration of the equipment during use, and ensure good heat dissipation conditions.
开机之前一定要在设备中倒入清洗液,而且被清洗的物品是不能够和清洗机的槽底结束的。好能够把工件放到篮筐中,这样能够保护好机器,也能够让物品得到充分的清洗。
Before starting the machine, the detergent must be poured into the equipment, and the cleaned items cannot end up with the bottom of the washer. So that the workpiece can be put into the basket, which can protect the machine and fully clean the articles.
不能选择强酸或者强碱性的清洗液,带有腐蚀性或者有毒性的清洗液更加要慎用了。
It is not allowed to choose strong acid or strong alkaline cleaning solution, especially those with corrosivity or toxicity.
正确使用步骤:
Steps for correct use:
1、参照超声波清洗机安装说明书,连接清洗机的电控柜与主机间的温控传感器信号线、超声驱动线、加热器控制线等线路,并接通380VAC电源,安装清洗机的上水管、放水管与溢流排放管。
1. Refer to the installation instructions of the ultrasonic cleaning machine, connect the temperature control sensor signal line, ultrasonic drive line, heater control line and other lines between the electric control cabinet of the cleaning machine and the host machine, connect the 380VAC power supply, and install the water supply pipe, drain pipe and overflow drain pipe of the cleaning machine.
全自动超声波清洗机
2、向清洗池内加入适量清水,液面高度以浸没将要清洗的零部件为准,一般不超过清洗池的3/4。
2. Add an appropriate amount of clean water into the cleaning pool, and the liquid level shall be subject to the immersion of the parts to be cleaned, generally not more than 3/4 of the cleaning pool.
3、启动电控加热开关,将水温调节旋钮上的白色刻度线指向适当的温度(应为60℃左右)。清洗机在使用过程中,清洗剂的高温度不应超过70℃。
3. Start the electric control heating switch and point the white scale mark on the water temperature regulating knob to the appropriate temperature (about 60 ℃). During the use of the cleaning machine, the high temperature of the cleaning agent shall not exceed 70 ℃.
4、待水温升至40℃左右时,将清洗剂加入清洗池中,搅动清水使其充分溶解(此时亦可启动超声波或开启鼓气装置进行搅拌)。
4. When the water temperature rises to about 40 ℃, add the cleaning agent into the cleaning pool and stir the clean water to fully dissolve it (at this time, the ultrasonic wave can also be started or the air blowing device can be started to stir).
5、清洗之前宜用竹刀先将零部件表面的污垢简单清洁一下,超声波能够进行清洗,但其对泥类的污物处理能力较弱,故预处理中,应尽量将黄泥或稀泥类的污物去除。
5. Before cleaning, it is advisable to use a bamboo knife to simply clean the dirt on the surface of parts. Ultrasonic can clean, but its ability to treat mud is weak. Therefore, yellow mud or mud should be removed as much as possible during pretreatment.
所以,在进行超声波清洗机操作的时候,以上的这些事项是一定要注意的,只有这样才能更好的完成任务。更多相关内容就来我们网站www.jnthcsb.com咨询了解吧!
Therefore, the above matters must be paid attention to when operating the ultrasonic cleaning machine. Only in this way can we better complete the task. Come to our website www.jnthcsb.com for more information!