欢迎访问济南科尔超声波设备有限公司网站!

专注生产工业用清洗设备

让工业清洗无难事

电话

业务咨询电话:

18663767799

你所在位置: 首页-新闻动态-新闻资讯-全自动超声波清洗机的恰当开机流程介绍
新闻资讯

全自动超声波清洗机的恰当开机流程介绍

作者:guanli来源:http://www.jnthcsb.com/时间:2021-11-22

恰当应用超声波清洗机的实际意义坚信大家都清晰,尤其是开机。为了更好地更快的应用超声波清洗机,下面为各位介绍一下超声波清洗机的恰当开机流程。一,保证 沒有脏东西落入超声波清洗机内腔底端,若有务必消除。
The practical significance of proper application of ultrasonic cleaning machine is firmly believed that everyone is clear, especially when starting up. In order to better and faster apply the ultrasonic cleaning machine, let's introduce the appropriate startup process of the ultrasonic cleaning machine. 1、 Ensure that no dirt falls into the bottom of the inner cavity of the ultrasonic cleaning machine. If any, be sure to eliminate it.
二,超声波槽温度做到设置所须要的加温温度,显示灯灭掉,温度掣全自动关闭电源,秸杆处于全自动控温情况。
2、 The temperature of the ultrasonic tank shall be set to the required heating temperature, the display light shall be off, the temperature switch shall automatically turn off the power supply, and the straw shall be under full-automatic temperature control.
三,清洗液的高宽比也会危害清洗品质,对不一样物品的清洗部位应探索其较好部位(注:清洗液的量与清洗槽的容积之比2/3)。
3、 The aspect ratio of cleaning fluid will also endanger the cleaning quality. For the cleaning parts of different articles, the better parts should be explored (Note: the ratio of the amount of cleaning fluid to the volume of the cleaning tank is 2 / 3).
全自动超声波清洗机
四,将工件装进清洗篮具,按清洗程序流程开展工件清洗。
4、 Put the workpiece into the cleaning basket and clean the workpiece according to the cleaning procedure.
五,流动性水中基本清洗器械后,将器械放进超声波清洗机清洗过滤管内,务必应用清洗过滤管运载,全自动超声波清洗线立即置放在超声波清洗机内腔底端清洗。器械务必充足开启,可拆卸的器械分离出来各部件;塑料吸管等长细空心器械张口朝下歪斜置放,确使腔内灌满水溶液,清洗液液位泡过器械50mm。
5、 After basically cleaning the instrument in flowing water, put the instrument into the cleaning filter tube of the ultrasonic cleaning machine. Be sure to carry it with the cleaning filter tube. The full-automatic ultrasonic cleaning line shall be immediately placed at the bottom of the inner cavity of the ultrasonic cleaning machine for cleaning. The instrument must be fully opened, and the detachable instrument must separate all parts; The plastic straw and other long and thin hollow instruments are placed obliquely with the opening downward, so as to ensure that the cavity is filled with aqueous solution, and the liquid level of cleaning solution is 50 mm above the instrument.
六,盖好超声波清洗机的外盖,设定清洗時间,逐渐超声波清洗。超声波清洗時间在3~5min,假如油水分离结构超声波精度很高的工件不适合超出10min。
6、 Cover the outer cover of the ultrasonic cleaning machine, set the cleaning time and gradually ultrasonic cleaning. The ultrasonic cleaning time is 3 ~ 5min. If the oil-water separation structure, the workpiece with high ultrasonic accuracy is not suitable for more than 10min.
七,进行作业后,设备要停止工作,取下工件,关闭全部电源总开关就可以。
7、 After the operation, the equipment should stop working, remove the workpiece and turn off all the main power switches.